Page 41 - ISCAR FACE GROOVING LINES
P. 41
LH FACE GROOVE-TURN
HGHR/L-3 H OAH
Integral Holders for Face
Grooving and Turning DAXN-DAXX CDX HBH OAW
CDX OAL
WF CW B
Right-hand shown
METRIC
Designation H B CW CDX HBH WF DAXN(1) DAXX(2) OAL LH OAH OAW
HGHR 1010-12-3T6 10.0 10.0 3.00 6.00 2.0 9.50 12.0 16.0 120.00 19.0 19.0 13.70 SR 76-1400 T-20/3
HGHR 1010-16-3T6 10.0 10.0 3.00 6.00 2.0 9.50 16.0 25.0 120.00 19.0 19.0 12.80 SR 76-1400 T-20/3
HGHR/L 1212-12-3T6 12.0 12.0 3.00 6.00 - 11.00 12.0 16.0 120.00 19.0 19.0 15.70 SR 76-1400 T-20/3
HGHR 1212-16-3T6 12.0 12.0 3.00 6.00 - 11.00 16.0 25.0 120.00 19.0 19.0 14.80 SR 76-1400 T-20/3
HGHR/L 1616-12-3T6 16.0 16.0 3.00 6.00 - 15.00 12.0 16.0 120.00 19.0 21.0 19.70 SR 76-1400 T-20/3
HGHR/L 1616-16-3T6 16.0 16.0 3.00 6.00 - 15.00 16.0 25.0 120.00 19.0 21.0 18.80 SR 76-1400 T-20/3
HGHR/L 2020-12-3T6 20.0 20.0 3.00 6.00 - 20.00 12.0 16.0 120.00 19.0 25.0 24.00 SR 76-1400 T-20/3
HGHR/L 2020-16-3T6 20.0 20.0 3.00 6.00 - 20.00 16.0 25.0 120.00 19.0 25.0 24.00 SR 76-1400 T-20/3
HGHR/L 2525-12-3T6 25.0 25.0 3.00 6.00 - 25.00 12.0 16.0 120.00 19.0 30.0 29.00 SR 76-1400 T-20/3
HGHR/L 2525-16-3T6 25.0 25.0 3.00 6.00 - 25.00 16.0 25.0 120.00 19.0 30.0 29.00 SR 76-1400 T-20/3
• HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: GRIP (70) • GRIP (full radius) (72) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)
Groove can be widened with no limitation toward or away d
from the center except for the following tools: D
HGHR/L...-12-3T6 Limitation of widening toward center
Dd depends on the major diameter (D) as
12.0 4.0 per chart.
13.0 1.0
13.5 0
LH
HGHR/L-3 H OAH
Integral Holders for Face
Grooving and Turning DAXN-DAXX CDX HBH OAW
OAL
CDX
WF CW B
Right-hand shown
INCH
Designation CW CDX H B HBH DAXN(1) DAXX(2) WF OAH OAW OAL LH
HGHL 9.5-12-3T6 .118 .236 .375 .375 .12 .47 .63 .370 .67 .559 5.000 .750 SR 76-1400 T-20/3
HGHL 12.7-12-3T6 .47 .63 .460 .70 .646 5.000 .750 SR 76-1400 T-20/3
HGHL 12.7-16-3T6 .118 .236 .500 .500 .12 .63 .98 .460 .70 .619 5.000 .750 SR 76-1400 T-20/3
HGHR/L 15.9-12-3T6 .47 .63 .590 .82 .771 5.000 .750 SR 76-1400 T-20/3
HGHR/L 19-12-3T6 .118 .236 .500 .500 .12 .47 .63 .750 .95 .907 5.000 .750 SR 76-1400 T-20/3
HGHR/L 19-16-3T6 .63 .98 .750 .95 .907 5.000 .750 SR 76-1400 T-20/3
HGHR/L 25.4-12-3T6 .118 .236 .625 .625 .12 .47 .63 1.000 1.20 1.157 5.000 .750 SR 76-1400 T-20/3
HGHR/L 25.4-16-3T6 .63 .98 1.000 1.20 1.157 5.000 .750 SR 76-1400 T-20/3
HGHR 9.5-16-3T6 .118 .236 .750 .750 - .63 .98 .370 .67 .524 5.000 .750 SR 76-1400 T-20/3
HGHR 15.9-16-3T6 .63 .98 .590 .82 .735 5.000 .750 SR 76-1400 T-20/3
.118 .236 .750 .750 -
.118 .236 1.000 1.000 -
.118 .236 1.000 1.000 -
.118 .236 .375 .375 .12
.118 .236 .625 .625 .12
• HGN & GRIP inserts can be used only with right-hand toolholders, HGPL inserts only with left-hand toolholders • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: GRIP (70) • GRIP (full radius) (72) • HGN-C (76) • HGN-J (77) • HGN-UT (78) • HGPL (75)
Groove can be widened with no limitation toward or away d
from the center except for the following tools: D
HGHR/L...-12-3T6 Limitation of widening toward center
Dd depends on the major diameter (D) as
per chart
.472 .157
.512 .039
.513 0
39
