Page 46 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN LH

HFHR/L-5T CDX H H OAH
Integral Toolholders for DAXN-DAXX CW B
External Facing HFHR/L --5T10 HBH
WF OAL
WF2
Right-hand shown
CDX
.826

INCH

Designation CW CDX H B OAL F1 WF DAXN(1) DAXX(2) LH OAH

HFHR/L 25.4-25-5T10 .197 .390 1.000 1.000 6.000 .28 1.040 .98 1.18 1.500 1.31 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-28-5T15 .197 .670 1.000 1.000 6.000 - 1.040 1.10 1.22 1.340 1.39 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-31-5T15 .197 .670 1.000 1.000 6.000 - 1.040 1.22 1.38 1.340 1.39 SR M6X16 DIN912 HW 5.0
HFHR 25.4-35-5T20 .197 .790 1.000 1.000 6.000 - 1.040 1.38 1.57 1.540 1.43 SR M6X16 DIN912 HW 5.0
HFHR 25.4-40-5T20 .197 .790 1.000 1.000 6.000 - 1.040 1.57 1.77 1.540 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-55-5T25 .197 .980 1.000 1.000 6.000 - 1.040 2.17 2.76 1.730 1.43 SR M6X16 DIN912 HW 5.0
HFHR 25.4-45-5T25 .197 .980 1.000 1.000 6.000 - 1.040 1.77 2.17 1.730 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-70-5T32 .197 1.260 1.000 1.000 6.000 - 1.040 2.76 3.74 2.000 1.43 SR M6X16 DIN912 HW 5.0
HFHR/L 25.4-95-5T32 .197 1.260 1.000 1.000 6.000 - 1.040 3.74 5.12 2.000 1.43 SR M6X16 DIN912 HW 5.0

• DGN & GRIP 5.. inserts can be used only with right-hand tools, HGPL 5.. inserts with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: DGN-W (81) • DGN/DGNC/DGNM-C (79) • DGN/DGNM-J/JS/JT (82) • GRIP (70) • GRIP (full radius) (72) • GRIPA (73)
• GRIPA (full radius) (74) • HFPR/L (68) • HFPR/L (full radius) (69) • HGPL (75)

Groove can be widened with no limitation toward or away
from the center except for the following tools:

HFHR/L-#-31-5T15 HFHR/L-#-28-5T15 HFHR/L-#-25-5T10 d
D
D d D d D d Limitation of widening
1.22 .59 1.10 .51 .98 .16 toward center (d)
1.26 .39 1.14 .31 1.02 .04 depends on the major
1.30 .28 1.18 .20 ≥1.06 0 diameter (D) as per
1.34 .16 1.22 .12 chart
1.38 .08 1.29 .04
≥1.42 0 ≥1.30 0

44 ISCAR