Page 43 - ISCAR FACE GROOVING LINES

LH FACE GROOVE-TURN

HFHR/L-4T CDX HF H OAH
Integral Holders for Facing DAXN-DAXX CW B
HFHR/L --4T12
WF HBH
WF2 OAL

CDX

Right-hand shown

METRIC

Designation CW CDX H HF B OAL WF WF2 DAXN(1) DAXX(2) LH OAH HBH

HFHR/L 20-25-4T12 4.00 12.00 20.0 20.0 20.0 140.00 20.60 6.2 25.0 29.0 39.0 29.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-29-4T12 4.00 12.00 20.0 20.0 20.0 140.00 20.60 6.2 29.0 34.0 39.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-25-4T12 4.00 12.00 25.0 25.0 25.0 150.00 25.60 6.2 25.0 29.0 39.0 34.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-29-4T12 4.00 12.00 25.0 25.0 25.0 150.00 25.60 6.2 29.0 34.0 39.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-34-4T20 4.00 20.00 20.0 20.0 20.0 140.00 20.60 - 34.0 40.0 39.0 30.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-34-4T20 4.00 20.00 25.0 25.0 25.0 150.00 25.60 - 34.0 40.0 39.0 35.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-40-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 40.0 48.0 44.0 31.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-48-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 48.0 60.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-60-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 60.0 75.0 44.0 32.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 20-75-4T25 4.00 25.00 20.0 20.0 20.0 140.00 20.60 - 75.0 100.0 44.0 34.0 2.0 SR M6X16 DIN912 HW 5.0
HFHL 25-100-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 100.0 140.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-140-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.74 - 140.0 240.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-240-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 240.0 800.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-40-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 40.0 48.0 44.0 36.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-48-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 48.0 60.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR/L 25-60-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 60.0 75.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHL 25-75-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 75.0 100.0 44.0 37.0 - SR M6X16 DIN912 HW 5.0
HFHR 25-100-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.74 - 100.0 140.0 44.0 37.0 -
HFHR 25-140-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.60 - 140.0 240.0 44.0 37.0 -
HFHR 25-75-4T25 4.00 25.00 25.0 25.0 25.0 150.00 25.80 - 75.0 100.0 44.0 37.0 -

• DGN & GRIP 4 mm inserts can be used only with right-hand tools, HGPL 4 mm with left-hand tools • For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: DGN-MF (80) • HFPR/L (68) • HFPR/L (full radius) (69) • GRIP (70) • GRIP (full radius) (72) • DGN/DGNC/DGNM-C (79)
• DGN/DGNM-J/JS/JT (82) • HGPL (75)

Groove can be widened with no limitation toward or away
from the center except for the following tools:

HFHR/L-#-25-4T12 HFHR/L-#-29-4T12 Limitation of widening toward d
Dd Dd center (d) depends on the major D
25 1 29 1 diameter (D) as per chart
≥26 0 ≥46 0

41