Page 92 - ISCAR FACE GROOVING LINES
P. 92
FACE GROOVE-TURN GIF-E (W=8,10) ±0.025 30 Ref.
Precision Double-Ended Inserts
for Grooving and Turning 7° 6.4
BW
CW
RE
METRIC
Dimensions Tough 1 Hard Recommended
Machining Data
f
f turn groove
IC830 ap (mm/ (mm/
Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) IC8250 (mm) rev) rev)
8.00 0.40 0.02 0.030 IC808
GIF 8.00E-0.40 8.00 0.80 0.02 0.050 IC908
GIF 8.00E-0.80 8.00 1.20 0.02 0.050 IC20
GIF 8.00E-1.20 10.00 0.80 0.02 0.050 IC5010
GIF 10.00E-0.80 10.00 1.20 0.02 0.050 IC428
GIF 10.00E-1.20 IC806
IC807
6.00 27.00 ••• 0.50-4.80 0.29-0.48 0.18-0.31
6.00 27.00 • • • • • • • • • 1.00-4.80 0.32-0.56 0.18-0.34
6.00 27.00 • • • • • • • 1.45-4.80 0.32-0.62 0.18-0.34
8.00 27.00 • • • • • • • • 1.00-6.00 0.35-0.65 0.22-0.40
8.00 27.00 • • • • • • 1.45-6.00 0.35-0.72 0.22-0.40
• DMIN for internal machining = 65 mm • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum
For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)
GIF-E (W=.315,.394) ±.001 1.18 Ref.
Precision Double-Ended Inserts
for Grooving and Turning 7° .252
BW
CW
RE
Dimensions INCH Recommended Machining Data
Tough 1 Hard
Designation CW RE CWTOL(1) RETOL(2) BW CDX(3) IC830 ap f turn f groove
.0012 IC8250
.0020 IC808 (inch) (IPR) (IPR)
.0020 IC908 .020-.189 .0114-.0189 .0071-.0122
.0020 IC20 .039-.189 .0126-.0220 .0071-.0134
.0020 IC5010 .057-.189 .0126-.0244 .0071-.0134
IC428 .039-.236 .0138-.0256 .0087-.0157
IC806 .057-.236 .0138-.0283 .0087-.0157
IC807
GIF 8.00E-0.40 .315 .0160 .0008 .236 1.063 •••
.236 1.063 • • • • • • • • •
GIF 8.00E-0.80 .315 .0315 .0008 .236 1.063 • • • • • • •
GIF 8.00E-1.20 .315 .0472 .0008 .315 1.063 • • • • • • • •
GIF 10.00E-0.80 .394 .0315 .0008 .315 1.063 • • • • • •
GIF 10.00E-1.20 .394 .0472 .0008
• DMIN for internal machining = 2.56" • For cutting speed recommendations and user guide, see pages 161-173
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)
(3) Cutting depth maximum
For tools, see pages: • GAFG-R/L-8 (87) • GHFG-R/L-8 (83) • GHFGR/L-8 (84)
90 ISCAR
