Page 86 - ISCAR FACE GROOVING LINES
P. 86
FACE GROOVE-TURN GHFGR/L-8 CDX LH H
Holders for Face Grooving HF B
and Turning
DAXN-DAXX HBH
OAL
WF Right-hand shown
CW
METRIC
Designation CDX DAXN(1) DAXX(2) H HF B CW OAL LH WF HBH
GHFGR/L 25-80-8 23.00 80.0 115.0 25.0 25.0 25.0 8.00 150.00 43.5 21.30 6.0 SR M6X20 DIN912 HW 5.0
GHFGR/L 32-80-8 SR M6X20 DIN912 HW 5.0
23.00 80.0 115.0 32.0 32.0 32.0 8.00 170.00 43.5 28.30 - SR M6X20 DIN912 HW 5.0
GHFGR/L 25-105-8 SR M6X20 DIN912 HW 5.0
25.00 105.0 160.0 25.0 25.0 25.0 8.00 150.00 43.5 21.30 6.0 SR M6X20 DIN912 HW 5.0
GHFGR/L 32-105-8 SR M6X20 DIN912 HW 5.0
25.00 105.0 160.0 32.0 32.0 32.0 8.00 170.00 43.5 28.30 -
GHFGR/L 25-155-8
GHFGR/L 32-155-8 25.00 155.0 510.0 25.0 25.0 25.0 8.00 150.00 43.5 21.30 6.0
25.00 155.0 510.0 32.0 32.0 32.0 8.00 170.00 43.5 28.30 -
• No limitation to widening the groove either way after initial grooving • CDX depends on the penetration diameter and the insert
• For user guide, see pages 161-173
(1) Minimum penetration diameter
(2) Maximum penetration diameter
For inserts, see pages: GDMF (100) • GDMM-CC (108) • GDMN (98) • GDMU (99) • GDMY (95) • GDMY (full radius) (96) • GDMY-F (97)
• GIA-K (long pocket) (93) • GIF (long pocket) (91) • GIF-E (W=8,10 full radius) (92) • GIF-E (W=8,10) (90) • GIFG-E (W=8) (89)
• GIPA/GIDA 8 (full radius) (105)
CDX for GHFGR/L (25/32)-80-8
D GIF 8… GIFG 8… GDMY 8… GIPA 8… GIDA 8… GIA 8… GDMM 8CC…
80 16 23 16 24
82 17 23 23 20 24 17 24
84 18 23 18 24
86 19 23 23 20 24 19 24
88 20 23 20 24
90 20 23 23 21 24 20 24
96 20 23 20 24
104 20 23 23 21 24 20 24
115 22 23 22 24
23 22 24
D GIF 8… GIFG 8… GIA 8… GDMM 8CC…
105 21 23 23 22 24 21 24
114 22 23 22 24
126 23 23 23 22 24 23 24
140-160 24 24 24 24
23 22 24
D GIF 8… GIFG 8… GIA 8… GDMM 8CC…
155 24 24 23 22 24 24 24
180 24 24 24 24
210-510 24 24 CDX for GHFGR/L (25/32)-105-8 24 24
GDMY 8… GIPA 8… GIDA 8…
23 23 24
23 23 24
24 23 24
24 23 24
CDX for GHFGR/L (25/32)-155-8
GDMY 8… GIPA 8… GIDA 8…
24 23 24
24 23 24
24 23 24
84 ISCAR
