Page 16 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN PICCO-010-N OAL DAXN
(Full Radius for
Face Grooving) a DCONMS Recommended
Inserts with Internal CW RE Machining Data
Coolant Channel for Round CDX
Profile Face Grooving LU

METRIC
Dimensions

Designation DAXN(1) CW RE CDX DCONMS a LU OAL IC908 f face-groove

PICCO R 010.1005-10N 8.0 1.00 0.50 2.00 7.05 5.90 9.0 32.00 • (mm/rev)
PICCO R 010.1005-20N 8.0 1.00 19.0 41.00 • 0.01-0.04
PICCO R 010.1608-10N 8.0 1.60 0.50 2.00 7.05 5.90 9.0 32.00 • 0.01-0.04
PICCO R 010.1608-20N 8.0 1.60 19.0 41.00 • 0.01-0.05
PICCO R 010.2010-10N 8.0 2.00 0.80 3.00 7.05 5.90 9.0 32.00 • 0.01-0.05
PICCO R 010.2010-20N 8.0 2.00 19.0 41.00 • 0.02-0.05
PICCO R 010.2512-10N 8.0 2.50 0.80 3.00 7.05 5.90 9.0 32.00 • 0.02-0.05
PICCO R 010.3015-10N 8.0 3.00 9.0 32.00 • 0.02-0.05
PICCO R 010.3015-20N 8.0 3.00 1.00 4.00 7.05 5.90 19.0 41.00 • 0.02-0.05
0.02-0.05
1.00 4.00 7.05 5.90

1.25 5.00 7.05 5.90

1.50 6.00 7.05 5.90

1.50 6.00 7.05 5.90

INCH

Dimensions Recommended
Machining Data

Designation DAXN(1) CW RE CDX DCONMS a LU OAL IC908 f face-groove

PICCO R 010.1005-10N .31 .039 .0197 .079 .278 .232 .354 1.260 • (IPR)
PICCO R 010.1005-20N .31 .039 .0197 .079 .278 .232 .748 1.614 • .0004-.0016
PICCO R 010.1608-10N .31 .063 .0315 .118 .278 .232 .354 1.260 • .0004-.0016
PICCO R 010.1608-20N .31 .063 .0315 .118 .278 .232 .748 1.614 • .0004-.0020
PICCO R 010.2010-10N .31 .079 .0394 .157 .278 .232 .354 1.260 • .0004-.0020
PICCO R 010.2010-20N .31 .079 .0394 .157 .278 .232 .748 1.614 • .0008-.0020
PICCO R 010.2512-10N .31 .098 .0492 .197 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.3015-10N .31 .118 .0590 .236 .278 .232 .354 1.260 • .0008-.0020
PICCO R 010.3015-20N .31 .118 .0590 .236 .278 .232 .748 1.614 • .0008-.0020
.0008-.0020

• Only right-hand inserts are available as standard, left-hand inserts on request • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only

• For detailed cutting data, see pages 162-164

(1) Minimum axial grooving diameter

14 ISCAR