Page 12 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN PICCO

IC908PICCO-010/610-NOALDAXN
(Face Grooving)
Inserts with Internal Coolant a DCONMS Recommended
Channel for Face Grooving CW Machining Data

CDX
LU

METRIC
Dimensions

f face-groove

Designation DAXN(1) CW CDX DCONMS a LU OAL (mm/rev)
32.00 •
PICCO R 010.1006-10N 6.0 1.00 1.50 6.05 5.20 9.0 32.00 • 0.01-0.04
PICCO R 010.1506-10N 6.0 1.50
PICCO R 010.1008-10N 8.0 1.00 2.00 6.05 5.20 9.0 32.00 • 0.01-0.04
PICCO R 010.1008-20N 8.0 1.00
PICCO R 010.1008-30N 8.0 1.00 1.50 7.05 5.90 9.0 41.00 • 0.01-0.04
PICCO R 610.1008-10N 8.0 1.00
PICCO R/L 010.1508-20N 8.0 1.50 1.50 7.05 5.90 19.0 51.00 • 0.01-0.04
PICCO R 010.1508-10N 8.0 1.50
PICCO R 010.1508-30N 8.0 1.50 1.50 7.05 5.90 29.0 32.00 • 0.01-0.04
PICCO R 610.1508-10N 8.0 1.50
PICCO R 610.1508-20N 8.0 1.50 1.50 6.05 5.20 9.0 41.00 • 0.01-0.04
PICCO R/L 010.2008-30N 8.0 2.00
PICCO R 010.2008-10N 8.0 2.00 2.50 7.05 5.90 19.0 32.00 • 0.01-0.04
PICCO R 010.2008-20N 8.0 2.00
PICCO R 610.2008-10N 8.0 2.00 2.50 7.05 5.90 9.0 51.00 • 0.01-0.04
PICCO R 610.2008-20N 8.0 2.00
PICCO R 010.2508-10N 8.0 2.50 2.50 7.05 5.90 29.0 32.00 • 0.01-0.04
PICCO R 010.2508-20N 8.0 2.50
PICCO R 610.2508-10N 8.0 2.50 2.50 6.05 5.20 9.0 41.00 • 0.01-0.04
PICCO R 010.3008-10N 8.0 3.00
PICCO R 010.3008-20N 8.0 3.00 2.50 6.05 5.20 19.0 51.00 • 0.01-0.04
PICCO R 010.3008-30N 8.0 3.00
PICCO R 610.3008-10N 8.0 3.00 3.00 7.05 5.90 29.0 32.00 • 0.02-0.05
PICCO R 610.3008-20N 8.0 3.00
3.00 7.05 5.90 9.0 41.00 • 0.02-0.05

3.00 7.05 5.90 19.0 32.00 • 0.02-0.05

3.00 6.05 5.20 9.0 41.00 • 0.02-0.05

3.00 6.05 5.20 19.0 32.00 • 0.02-0.05

3.50 7.05 5.90 9.0 41.00 • 0.02-0.05

3.50 7.05 5.90 19.0 32.00 • 0.02-0.05

3.50 6.05 5.20 9.0 32.00 • 0.02-0.05

3.50 7.05 5.90 9.0 41.00 • 0.02-0.06

3.50 7.05 5.90 19.0 51.00 • 0.02-0.06

3.50 7.05 5.90 29.0 32.00 • 0.02-0.06

3.50 6.05 5.20 9.0 41.00 • 0.02-0.06

3.50 6.05 5.20 19.0 0.02-0.06

• Only right-hand inserts are available as standard • All inserts are with sharp corners • Solid tools are suitable for PICCO-N / PICCO ACE-N type holders only
• For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter

10 ISCAR