Page 14 - Parting 4 Productivity inch

±.004
DGN/DGNM-J/JS/JT DGN 1002 DGNM
Double-Sided Inserts for Parting 7°
and Grooving Soft Materials, RE
Parting Tubes, Small Diameters INSL CDX
and Thin-Walled Parts CW

Recommended
Dimensions Tough 1 Hard
Machining Data

IC328 IC830 IC928 IC1030 IC1028 IC354 IC5400 IC1010 IC308 IC808 IC908 IC807 IC907 f groove
Designation CW CWTOL (3) RE RETOL (4) CDX INSL IC20 (IPR)
DGN 1002J .039 .0008 .006 .0008 .118 .827 • • • .0008-.0027
DGN 1402J .055 .0012 .006 .0008 .591 .622 • • • • • • • .0012-.0047
DGN 1502J .059 .0012 .006 .0008 .709 .823 • • • .0012-.0047
DGN 2002JT .079 .0012 .008 .0008 .709 .780 • .0016-.0055
DGN 2200JS (1) .087 .0012 .001 .0008 .709 .764 • • .0012-.0031
DGN 2202J .087 .0012 .008 .0008 .709 .780 • • • • • • • • • • • • .0016-.0047
DGN 2202JT .087 .0012 .008 .0008 .709 .780 • • • .0016-.0055
DGN 3100JS (1) .122 .0016 .001 .0008 .709 .776 • • .0012-.0039
DGN 3102J .122 .0016 .008 .0008 .709 .791 • • • • • • • • • • • • .0016-.0063
DGN 3102JT .122 .0016 .008 .0008 .709 .791 • • • • .0020-.0071
DGN 3202J .125 .0016 .008 .0008 .709 .827 • .0016-.0063
DGNM 3202J (2) .125 .0016 .008 .0008 - (5) .799 • • • .0016-.0063
DGN 4003J .157 .0016 .012 .0008 - .744 • • • • • • • • • .0020-.0071
(5)
DGN 4003JT .157 .0016 .012 .0012 - .744 • .0020-.0071
(5)
DGN 4803J .189 .0016 .012 .0008 - .803 • .0020-.0079
(5)
DGN 5003J .197 .0016 .012 .0008 - .748 • • • • • • • .0020-.0079
(5)
DGN 5003JT .197 .0016 .012 .0008 - .748 • • .0020-.0079
DGN 6303J .250 .0016 .014 .0008 - .752 • • • • • • • .0020-.0098
(5)
DGN 6303JT .250 .0016 .014 .0008 - .752 • • .0020-.0098
• JT chipformer has the basic positive configuration of the J-type and a reinforced negative frontal edge; most suitable for soft materials at low to medium feeds
(1) Sharp corners
(2) Single-ended insert
(3) Cutting width tolerance (+/-)
(4) Corner radius tolerance (+/-)
(5) No depth limit

DGN-LF/LFT ±.004
Double-Sided Inserts for Parting
and Grooving Stainless Steel RE
CW
INSL
Recommended
Dimensions Tough 1 Hard
Machining Data

IC830 IC928 IC1030 IC5400 IC1010 IC808 IC908 f groove
Designation CW CWTOL (1) RE RETOL (2) CDX INSL (IPR)
DGN 2002LF .079 .0012 .008 .0000 .709 .780 • • • .0012-.0031
DGN 2202LF .087 .0012 .008 .0000 .709 .780 • • • • • .0012-.0031
DGN 3102LF .122 .0016 .008 .0000 .709 .791 • • • • • • • .0016-.0039
DGN 3102LFT .122 .0016 .008 .0000 .709 .831 • • .0016-.0047
• JT chipformer has the basic positive configuration of the J-type and a reinforced negative frontal edge. Most suitable for soft materials at low to medium feeds
(1) Cutting width tolerance (+/-)
(2) Corner radius tolerance (+/-)

12