Page 22 - ISCAR FACE GROOVING LINES

FACE GROOVE-TURN PICCO-016/020 OAL DCONMS 6.3 Bar Max
(Face Grooving) OHN DAXN
Inserts with Coolant Holes Right-hand shown
for Deep Face Grooving RE0.2
a Recommended
Machining Data
CW RE0.2

METRIC
Dimensions

Designation DAXN(1) CW OHN(2) DCONMS a OAL IC1008 f face-groove
(mm/rev)
PICCO R 016.0300-10 16.0 3.00 10.00 8.00 5.50 30.00
• 0.01-0.05
PICCO R 016.0300-20 16.0 3.00 20.00 8.00 5.50 40.00 • 0.01-0.05
• 0.01-0.05
PICCO R 016.0400-10 16.0 4.00 10.00 8.00 6.00 30.00 • 0.01-0.05
• 0.01-0.05
PICCO R 016.0400-20 16.0 4.00 20.00 8.00 6.00 40.00 • 0.01-0.04
• 0.01-0.04
PICCO R 020.0300-25 20.0 3.00 25.00 8.00 5.50 45.00 • 0.01-0.04
• 0.01-0.06
PICCO R 020.0300-30 20.0 3.00 30.00 8.00 5.50 50.00 • 0.01-0.06
• 0.01-0.05
PICCO R 020.0300-35 20.0 3.00 35.00 8.00 5.50 55.00 • 0.01-0.05
• 0.02-0.06
PICCO R 020.0300-40 20.0 3.00 40.00 8.00 5.50 60.00 • 0.02-0.06
• 0.02-0.06
PICCO R 020.0400-25 20.0 4.00 25.00 8.00 6.00 45.00 • 0.02-0.05
• 0.02-0.05
PICCO R 020.0400-30 20.0 4.00 30.00 8.00 6.00 50.00

PICCO R 020.0400-35 20.0 4.00 35.00 8.00 6.00 55.00

PICCO R 020.0400-40 20.0 4.00 40.00 8.00 6.00 60.00

PICCO R 020.0500-20 20.0 5.00 20.00 8.00 6.50 40.00

PICCO R 020.0500-25 20.0 5.00 25.00 8.00 6.50 45.00

PICCO R 020.0500-30 20.0 5.00 30.00 8.00 6.50 50.00

PICCO R 020.0500-35 20.0 5.00 35.00 8.00 6.50 55.00

PICCO R 020.0500-40 20.0 5.00 40.00 8.00 6.50 60.00

• All inserts have two coolant holes which may be used with coolant pressure up to 100 bars • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

PICCO-016/020 OAL .248 PSI Max
(Face Grooving) OHN DCONMS
Inserts with Coolant Holes Right-hand shown
for Deep Face Grooving RE.008 DAXN
a Recommended
Machining Data
CW RE.008

INCH
Dimensions

Designation DAXN(1) CW OHN(2) DCONMS a OAL IC1008 f face-groove
(IPR)
PICCO R 016.0300-10 .63 .118 .394 .315 .217 1.181
PICCO R 016.0300-20 .63 .118 .787 .315 .217 1.575 • .0004-.0020
PICCO R 016.0400-10 .63 .157 .394 .315 .236 1.181 • .0004-.0020
PICCO R 016.0400-20 .63 .157 .787 .315 .236 1.575 • .0004-.0020
PICCO R 020.0300-25 .79 .118 .984 .315 .217 1.772 • .0004-.0020
PICCO R 020.0300-30 .79 .118 1.181 .315 .217 1.969 • .0004-.0020
PICCO R 020.0300-35 .79 .118 1.378 .315 .217 2.165 • .0004-.0020
PICCO R 020.0300-40 .79 .118 1.575 .315 .217 2.362 • .0004-.0020
PICCO R 020.0400-25 .79 .157 .984 .315 .236 1.772 • .0004-.0020
PICCO R 020.0400-30 .79 .157 1.181 .315 .236 1.969 • .0004-.0024
PICCO R 020.0400-35 .79 .157 1.378 .315 .236 2.165 • .0004-.0024
PICCO R 020.0400-40 .79 .157 1.575 .315 .236 2.362 • .0004-.0020
PICCO R 020.0500-20 .79 .197 .787 .315 .256 1.575 • .0004-.0020
PICCO R 020.0500-25 .79 .197 .984 .315 .256 1.772 • .0010-.0024
PICCO R 020.0500-30 .79 .197 1.181 .315 .256 1.969 • .0010-.0024
PICCO R 020.0500-35 .79 .197 1.378 .315 .256 2.165 • .0010-.0024
PICCO R 020.0500-40 .79 .197 1.575 .315 .256 2.362 • .0010-.0020
• .0010-.0020

• All inserts have two coolant holes which may be used with coolant pressure up to 1450 PSI • For detailed cutting data, see pages 162-164
(1) Minimum axial grooving diameter
(2) Minimum overhang

20 ISCAR